Casting Steel Submersible Diaphragm Pump , Positive Displacement
Pump
Application and Advantage:
Pneumatic diaphragm pumps are operated with compressed air .
diaphragm pumps is suitable for pumping fluids with particles, and
various liquids, which are highly viscous, volatile, corrosive or
toxic, as well as colloids. The pump body is made of aluminum
alloys, cast iron or stainless steel. The diaphragm is made of high
quality rubber such as Nitrile rubber, chloronorgutta rubber,
fluoroine rubber. The diaphragm pumps are widely used in the
petroleum chemical, electronic, ceramic, food and textile
industries.
| Item | Description | Unit | Reference Figure |
| 1 | Maximum air inlet pressure | Mpa | 0.83 |
| 2 | Maximum flow rate | L/Min | 192 |
| 3 | Maximum lift | M | 70 |
| 4 | Maximum outlet pressure | Mpa | 0.83 |
| 5 | Maximum particle size | mm | 3 |
| 6 | Weight | kg | 12.3 |
| 7 | Noise level | db | ＜70 |
Specifications
Air Diaphragm Pump
1. Non leakage
2. Good self priming performance
3. Convey all kinds of medium
4. Material:Cast steel,Alu,SS,PP
General Description
Air diaphragm pump(also know as a Membrane pump, air operated double diaphragm pump(AOOD) or pneumatic diaphragm pump)that uses a combination of the reciprocating action of a
rubber,thermoplastic or diaphragm and suitable valves either side
of the diaphragm (check valve,butterfly valves,flap valves,or any
other form of shut-off valves) to pump a fluid.
The diaphragm pump offers high volume delivery even at low air
pressure and a b road range of material compatibility options
available.Refer to the model and option chart.The pump is provided
with the modularized air motor and fluid section.
The air operated diaphragm pump alternately generates the intake
fluid pressure and positive fluid pressure in the fluid chamber by
using the pressure difference in the air chamber. The ball valve
can ensure the forward flow of fluid.
Pump cycling will begin as air pressure is applied and it will
continue to pump and keep up with the demand. It will build and
maintain line pres -sure and will stop cycling once maximum line
pressure is reached (dis -pensing device closed) and will resume
pumping as needed.
A 2 5 X X - X X X - X (model selection)
Form of pipe mouth:A-BSP B-NPT(F) C-Flange
Diaphragm material:9 – Santoprene H – Hytrel T - PTFE/Santoprene
Ball material:9 -Santoprene H – Hytre T – PTFE A - Acetal
Ball seat material:P/K –Polypropylene/Kynoar SS –Stainless Steel
Pump material: SS –Stainless Steel AL –Aluminum Alloy CI- Carbon
Steel P/K –Polypropylene/Kynoar
Maximum Applied Temperature Limits (diaphragm / ball / seal material)
Acetal ·······································40°- 150°F (4.4-
65.5°C)
Santoprene··································-40°- 225°F (-40°-
107.2°C)
·········································40°- 220°F (4.4°- 104°C)
Nitrile··········································10°- 180°F (-12°-
82°C)
Viton···········································-40°- 350°F
(-40°-176.6°C)
Hytrel············································-20°-150°F (-12°-
93°C) Kynar············································10°-200°F
(-28.9°- 65.5°C)
Polypropylene···································32°- 175°F
(0-79.4°C)
1” Flow diagram
